18.4. Configuring a Network Connection with YaST

There are many supported networking types on Linux. Most of them use different device names and the configuration files are spread over several locations in the file system. For a detailed overview of the aspects of manual network configuration, see Section 18.6, “Configuring a Network Connection Manually”.

During installation, YaST can be used to configure automatically all interfaces that have been detected. Additional hardware can be configured any time after installation in the installed system. The following sections describe the network configuration for all types of network connections supported by SUSE Linux.

18.4.1. Configuring the Network Card with YaST

After starting the module, YaST displays a general network configuration dialog. Choose whether to use YaST or NetworkManager to manage all your network devices. To use NetworkManager, check User Controlled with NetworkManager. Find detailed information about NetworkManager in Section 18.5, “Managing Network Connections with NetworkManager”. If you want to configure your network in the traditional way with the YaST, check Traditional Method with ifup.

The upper part of the traditional configuration shows a list with all the network cards available for configuration. Any card properly detected is listed with its name. Devices that could not be detected may be configured using Add as described in Section 18.4.1.1, “Manual Configuration of an Undetected Network Card”. Configure a new network card or change an existing configuration.

18.4.1.1. Manual Configuration of an Undetected Network Card

Configuring a network card that was not detected includes the following items:

Network Configuration

Set the device type of the interface from the available options and the configuration name. Information about the naming conventions for configuration names is available in the getcfg(8) man page.

Kernel Module

Hardware Configuration Name specifies the name of the /etc/sysconfig/hardware/hwcfg-* file containing the hardware settings of your network card. This contains the name of the suitable kernel module as well as the needed options to initialize the hardware. Usually, YaST proposes useful names for PCMCIA and USB hardware. For other hardware, hwcfg-static-0 usually only makes sense if the card is configured with the configuration name 0.

If the network card is a PCMCIA or USB device, activate the respective check boxes and exit this dialog with Next. Otherwise, select your network card model from Select from List. YaST then automatically selects the suitable kernel module for the card. Exit this dialog with Next.

Figure 18.3. Configuration of the Network Card

Configuration of the Network Card

18.4.1.2. Setting the Network Address

Set the device type of the interface and the configuration name. Select the device type from those provided. Specify a configuration name according to your needs. Usually, the default settings are useful and can be accepted. Information about the naming conventions for configuration names is available in the getcfg(8) man page .

If you selected Wireless as the device type of the interface, configure the operating mode, the network name (ESSID), and the encryption in the next dialog, Wireless Network Card Configuration. Click OK to complete the configuration of your card. A detailed description of the configuration of WLAN cards is provided in Section 34.1.3, “Configuration with YaST”. For all other interface types, proceed with the network address setup:

Automatic Address Setup (via DHCP)

If your network includes a DHCP server, you can rely on it to set up your network address automatically. The option should also be used if you are using a DSL line but with no static IP assigned by the ISP. If you decide to use DHCP, configure the details after selecting DHCP Client Options. Specify whether the DHCP server should always honor broadcast requests and any identifier to use. By default, DHCP servers use the card's hardware address to identify an interface. If you have a virtual host setup where different hosts communicate through the same interface, an identifier is necessary to distinguish them.

Static Address Setup

If you have a static address, enable that option. Then enter the address and subnet mask for your network. The preset subnet mask should match the requirements of a typical home network.

Leave this dialog by selecting Next or proceed to configure the hostname, name server, and routing details (see the sections on DNS Server (↑Start-Up) and Routing (↑Start-Up)).

Advanced enables you to specify more complex settings. Under Detailed Settings, use User Controlled to delegate the control over the network card from the administrator (root) to the normal user. For mobile operation, this allows the user to adapt changing network connections in a more flexible way, because he can control the activation or deactivation of the interface. The MTU (maximum transmission unit) and the type of Device Activation can also be set in this dialog.

18.4.2. Modem

In the YaST Control Center, access the modem configuration under Network Devices. If your modem was not automatically detected, open the dialog for manual configuration. In the dialog that opens, enter the interface to which the modem is connected under Modem.

Figure 18.4. Modem Configuration

Modem Configuration

If you are behind a private branch exchange (PBX), you may need to enter a dial prefix. This is often a zero. Consult the instructions that came with the PBX to find out. Also select whether to use tone or pulse dialing, whether the speaker should be on, and whether the modem should wait until it detects a dial tone. The last option should not be enabled if the modem is connected to an exchange.

Under Details, set the baud rate and the modem initialization strings. Only change these settings if your modem was not autodetected or if it requires special settings for data transmission to work. This is mainly the case with ISDN terminal adapters. Leave this dialog by clicking OK. To delegate control over the modem to the normal user without root permissions, activate User Controlled. In this way, a user without administrator permissions can activate or deactivate an interface. Under Dial Prefix Regular Expression, specify a regular expression. The Dial Prefix in KInternet, which can be modified by the normal user, must match this regular expression. If this field is left empty, the user cannot set a different Dial Prefix without administrator permissions.

In the next dialog, select the ISP (Internet service provider). To choose from a predefined list of ISPs operating in your country, select Country. Alternatively, click New to open a dialog in which to provide the data for your ISP. This includes a name for the dial-up connection and ISP as well as the login and password provided by your ISP. Enable Always Ask for Password to be prompted for the password each time you connect.

In the last dialog, specify additional connection options:

Dial on Demand

If you enable dial on demand, set at least one name server.

Modify DNS when Connected

This option is enabled by default, with the effect that the name server address is updated each time you connect to the Internet.

Automatically Retrieve DNS

If the provider does not transmit its domain name server after connecting, disable this option and enter the DNS data manually.

Stupid Mode

This option is enabled by default. With it, input prompts sent by the ISP's server are ignored to prevent them from interfering with the connection process.

External Firewall Interface and Restart Firewall

Selecting these options enables the SUSEfirewall2, which protects you from outside attacks for the duration of your Internet connection.

Idle Time-Out (seconds)

With this option, specify a period of network inactivity after which the modem disconnects automatically.

IP Details

This opens the address configuration dialog. If your ISP does not assign a dynamic IP address to your host, disable Dynamic IP Address then enter your host's local IP address and the remote IP address. Ask your ISP for this information. Leave Default Route enabled and close the dialog by selecting OK.

Selecting Next returns to the original dialog, which displays a summary of the modem configuration. Close this dialog with Finish.

18.4.3. ISDN

Use this module to configure one or several ISDN cards for your system. If YaST did not detect your ISDN card, manually select it. Multiple interfaces are possible, but several ISPs can be configured for one interface. In the subsequent dialogs, set the ISDN options necessary for the proper functioning of the card.

Figure 18.5. ISDN Configuration

ISDN Configuration

In the next dialog, shown in Figure 18.5, “ISDN Configuration”, select the protocol to use. The default is Euro-ISDN (EDSS1), but for older or larger exchanges, select 1TR6. If you are in the US, select NI1. Select your country in the relevant field. The corresponding country code then appears in the field next to it. Finally, provide your Area Code and the Dial Prefix if necessary.

Start Mode defines how the ISDN interface should be started: At Boot Time causes the ISDN driver to be initialized each time the system boots. Manually requires you to load the ISDN driver as root with the command rcisdn start. On Hotplug, used for PCMCIA or USB devices, loads the driver after the device is plugged in. When finished with these settings, select OK.

In the next dialog, specify the interface type for your ISDN card and add ISPs to an existing interface. Interfaces may be either the SyncPPP or the RawIP type, but most ISPs operate in the SyncPPP mode, which is described below.

Figure 18.6. ISDN Interface Configuration

ISDN Interface Configuration

The number to enter for My Phone Number depends on your particular setup:

ISDN Card Directly Connected to Phone Outlet

A standard ISDN line provides three phone numbers (called multiple subscriber numbers, or MSNs). If the subscriber asked for more, there may be up to 10. One of these MSNs must be entered here, but without your area code. If you enter the wrong number, your phone operator automatically falls back to the first MSN assigned to your ISDN line.

ISDN Card Connected to a Private Branch Exchange

Again, the configuration may vary depending on the equipment installed:

  1. Smaller private branch exchanges (PBX) built for home purposes mostly use the Euro-ISDN (EDSS1) protocol for internal calls. These exchanges have an internal S0 bus and use internal numbers for the equipment connected to them.

    Use one of the internal numbers as your MSN. You should be able to use at least one of the exchange's MSNs that have been enabled for direct outward dialing. If this does not work, try a single zero. For further information, consult the documentation that came with your phone exchange.

  2. Larger phone exchanges designed for businesses normally use the 1TR6 protocol for internal calls. Their MSN is called EAZ and usually corresponds to the direct-dial number. For the configuration under Linux, it should be sufficient to enter the last digit of the EAZ. As a last resort, try each of the digits from 1 to 9.

For the connection to be terminated just before the next charge unit is due, enable ChargeHUP. However, remember that may not work with every ISP. You can also enable channel bundling (multilink PPP) by selecting the corresponding option. Finally, you can enable SuSEfirewall2 for your link by selecting External Firewall Interface and Restart Firewall. To enable the normal user without administrator permissions to activate or deactivate the interface, select the User Controlled.

Details opens a dialog in which to implement more complex connection schemes, which are not relevant for normal home users. Leave the Details dialog by selecting OK.

In the next dialog, make IP address settings. If you have not been given a static IP by your provider, select Dynamic IP Address. Otherwise, use the fields provided to enter your host's local IP address and the remote IP address according to the specifications of your ISP. If the interface should be the default route to the Internet, select Default Route. Each host can only have one interface configured as the default route. Leave this dialog by selecting Next.

The following dialog allows you to set your country and select an ISP. The ISPs included in the list are call-by-call providers only. If your ISP is not in the list, select New. This opens the Provider Parameters dialog in which to enter all the details for your ISP. When entering the phone number, do not include any blanks or commas among the digits. Finally, enter your login and the password as provided by the ISP. When finished, select Next.

To use Dial on Demand on a stand-alone workstation, also specify the name server (DNS server). Most ISPs support dynamic DNS, which means the IP address of a name server is sent by the ISP each time you connect. For a single workstation, however, you still need to provide a placeholder address like 192.168.22.99. If your ISP does not support dynamic DNS, specify the name server IP addresses of the ISP. If desired, specify a time-out for the connection—the period of network inactivity (in seconds) after which the connection should be automatically terminated. Confirm your settings with Next. YaST displays a summary of the configured interfaces. To make all these settings active, select Finish.

18.4.4. Cable Modem

In some countries, such as Austria and the US, it is quite common to access the Internet through the TV cable network. The TV cable subscriber usually gets a modem that is connected to the TV cable outlet on one side and to a computer network card on the other (using a 10Base-TG twisted pair cable). The cable modem then provides a dedicated Internet connection with a fixed IP address.

Depending on the instructions provided by your ISP, when configuring the network card either select Automatic Address Setup (via DHCP) or Static Address Setup. Most providers today use DHCP. A static IP address often comes as part of a special business account.

18.4.5. DSL

To configure your DSL device, select the DSL module from the YaST Network Devices section. This YaST module consists of several dialogs in which to set the parameters of DSL links based on one of the following protocols:

  • PPP over Ethernet (PPPoE)

  • PPP over ATM (PPPoATM)

  • CAPI for ADSL (Fritz Cards)

  • Point-to-Point Tunneling Protocol (PPTP)—Austria

The configuration of a DSL connection based on PPPoE or PPTP requires that the corresponding network card has already been set up in the correct way. If you have not done so yet, first configure the card by selecting Configure Network Cards (see Section 18.4.1, “Configuring the Network Card with YaST”). In the case of a DSL link, addresses may be assigned automatically but not via DHCP, which is why you should not enable the option Automatic address setup (via DHCP). Instead, enter a static dummy address for the interface, such as 192.168.22.1. In Subnet Mask, enter 255.255.255.0. If you are configuring a stand-alone workstation, leave Default Gateway empty.

[Tip]Tip

Values in IP Address and Subnet Mask are only placeholders. They are only needed to initialize the network card and do not represent the DSL link as such.

Figure 18.7. DSL Configuration

DSL Configuration

To begin the DSL configuration (see Figure 18.7, “DSL Configuration”), first select the PPP mode and the ethernet card to which the DSL modem is connected (in most cases, this is eth0). Then use Device Activation to specify whether the DSL link should be established during the boot process. Click User Controlled to authorize the normal user without root permissions to activate or deactivate the interface with KInternet. The dialog also lets you select your country and choose from a number of ISPs operating in it. The details of any subsequent dialogs of the DSL configuration depend on the options set so far, which is why they are only briefly mentioned in the following paragraphs. For details on the available options, read the detailed help available from the dialogs.

To use Dial on Demand on a stand-alone workstation, also specify the name server (DNS server). Most ISPs support dynamic DNS—the IP address of a name server is sent by the ISP each time you connect. For a single workstation, however, provide a placeholder address like 192.168.22.99. If your ISP does not support dynamic DNS, enter the name server IP address provided by your ISP.

Idle Time-Out (seconds) defines a period of network inactivity after which to terminate the connection automatically. A reasonable time-out value is between 60 and 300 seconds. If Dial on Demand is disabled, it may be useful to set the time-out to zero to prevent automatic hang-up.

The configuration of T-DSL is very similar to the DSL setup. Just select T-Online as your provider and YaST opens the T-DSL configuration dialog. In this dialog, provide some additional information required for T-DSL—the line ID, the T-Online number, the user code, and your password. All of these should be included in the information you received after subscribing to T-DSL.